Yamaha MG06 Mixer Set with Headphones

Yamaha has always aimed to offer its customers the purest, most uncolored sound possible, leaving the mixing engineer all doors open. While coloration may sometimes sound appealing, it imposes a clear direction on the mix that can strongly limit the producer's creative freedom. Naturally, the MG series was developed strictly according to this Yamaha belief. It follows the philosophy that sound should above all be pure and transparent like a mountain stream. Therefore, these consoles deliver a clarity of sound never before seen in this class.

D-PRE (Discrete Class-A Microphone Preamplifiers)

The preamps are the starting point for good sound. If their quality is insufficient, no great mix can be achieved, no matter how hard the engineer tries. In other words: this is where the course for the mix is set, or where a preliminary decision is made about how good it can sound. The MG series mixers feature Yamaha's studio-grade, discrete Class-A preamps. They use an inverted Darlington circuit, which thanks to a so-called dual-transistor cascade delivers more power at lower impedance. D-PRE amps provide a fat, natural bass and silky highs with extremely low distortion tendency.

Operational Amplifiers for Highest Sound Quality

The preamp determines sound quality, while the operational amplifier ICs are among the most important components of the preamp. The MG series features new, high-quality, custom-made MG01 operational amplifiers developed in close cooperation with the semiconductor manufacturer. While many other operational amplifiers optimize circuit design and efficiency, which are positive features, Yamaha prioritizes sound quality, so off-the-shelf chips were not an option.

Switchable Phantom Power and PAD Switch

Thanks to switchable phantom power, the MG series consoles allow connection of condenser microphones with all their advantages over dynamic microphones, including extended frequency response, much higher dynamics, and better sound quality. The input channels with PAD switch accept mic and line level signals. The PAD button attenuates high-level input signals, for example, miked instruments during a concert that might otherwise cause overloads, which could seriously damage the mix.

One-Button Compressors

Compression plays a key role in almost every studio production or live sound. By skillfully controlling the dynamics of audio signals with a compressor, you can create basslines with more punch, tighter snares, more present vocals, or thicker live guitar walls. However, it can take countless hours to master even simple hardware compressors and fully exploit them. Yamaha's innovative "One-Button" compressors allow optimal adjustment with just a single knob.

EQ and High-Pass Filter

Nothing beats a reliable equalizer when nuanced sound shaping is needed. The MG series benefits here from Yamaha's unparalleled experience in building audio devices. All mono channels feature excellent 3-band EQs for precise sound control. Additional high-pass filters allow removal of unwanted footstep noise and other low-frequency disturbances, making the mix noticeably clearer and cleaner.

AUX / Effect Sends / Groups

The MG series mixers feature AUX sends to expand the sound reinforcement or studio setup. These can be used to add effects, route outputs to external recording devices, or feed a monitoring system. The main mix also has its own send controls. The MG06 / 06X and MG10 / 10XU models have only one stereo main bus. Other models additionally have one or two stereo group buses and corresponding outputs for convenient channel grouping. Switches next to all channel faders allow clear group assignment.

Numerous Input and Output Connections

All models feature high-quality balanced Neutrik XLR connectors on mono channels. Stereo channels also have XLR jacks. Mono inputs are combo jacks accepting both MIC and LINE levels. Two stereo inputs have an XLR and two jack connectors. The XLR accepts MIC level signals, while the jacks are for LINE level. Mono or stereo line signals can be fed (except on the 10-channel model). The function of the other two stereo channels varies by model: on the 20-channel model, the XLR accepts MIC level, while two RCA connectors handle mono or stereo LINE signals.

Metal Housing

The MG series was built to last, featuring a solid, powder-coated metal housing of outstanding build quality. The shape optimally supports internal convection cooling, while the power supply is cleanly separated from the analog circuits inside, preventing noise and positively affecting component lifespan. Additionally, forces like pressure or pull on the mixer controls do not directly affect the circuit board or electronic components, as in many other mixers, but are absorbed by the sturdy housing, greatly enhancing reliability and durability.

Suitable accessories (Not included in the delivery.)

• K&M 19400 Stand Adapter